1. Preparation: Arrange the mattress, with correct position, even edges, no stains, no hair and no damage, and straighten and align the mattress.

2. Laying plates:

(1) Grasp one end of the bed sheet with the left hand (at the end of the bed), and grasp the edge of the other end (at the end of the bed) with the right hand to throw the bed sheet to the right (note: check the front and back of the bed sheet).

(2) Grab the thrown sheets and throw them to the bed, lift the sheets at the end of the bed, and grasp the sheets at the end of the bed with both hands (pay attention to the palm down, the distance between the hands is about 80- 100 cm, and the position of the hands is equal to the centerline distance).

(3) Lift the sheets at the end of the bed, let air enter the end of the bed, and make the sheets bulge. When it is about 70 cm away from the bed surface, lean forward slightly, spread the bed sheet completely with your wrist and arm, and lay it flat on the bed (note: when the air pushes the end of the bed sheet away, take the opportunity to adjust the bed sheet to make it fall on the correct position of the mattress accurately).

(4) Requirements: invoicing, throwing and invoicing positioning are successful at one time; The center line of the bed sheet is centered and does not deviate from the center line of the mattress; The front of the bed sheet is facing upward, and the surface is smooth (note: if the center line of the bed sheet is off-center, the angle should be wrapped from the short side of the bed sheet to facilitate the adjustment of the center line).

(5) Wrap the angle clockwise or counterclockwise from the bedside.

Take the right corner of the bed as an example: first tuck the right half of the bed sheet under the mattress, lift the bed sheet along the extension line of the bed with your left hand, put the extra bed sheet under the corner of the mattress with your right hand, conveniently pull the right side of the drooping bed sheet to be perpendicular to the horizontal line, and then tuck the extra bed sheet under the mattress to form an inner angle of 45 degrees and an outer angle of 90 degrees.

The other three corners are wrapped in the same way in turn, requiring tight, straight and flat corners and uniform styles; The four sides are tightly gathered and flat.

3, quilt cover:

(1) Stand at the end of the bed, lift off the front of the quilt cover and throw it at the head of the bed like a sheet (note: the quilt cover opens towards the end of the bed; Can't fall to the ground before quilt cover)

(2) Grasp the quilt cover at the end of the bed with both hands, throw it away at one time and lay it flat on the bed.

(3) Open the opening of the quilt cover and put the folded quilt core into the opening (pay attention to the stacking method of the quilt core on the workbench before putting it in).

(4) Find the front two corners of the quilt core, put them into the quilt cover at one time, plug the top of the quilt cover with the head of the quilt core, shake off the quilt core, throw the front of the quilt core upward with both hands, put the two corners behind the quilt core into the quilt cover, arrange the two sides of the quilt core at the same time, locate the four corners, flatten the gap between the quilt core and the quilt cover, and then tie a bandage on the opening of the quilt cover.

(5) Throw away the duvet, pull the quilt head to be flush with the bed head of the mattress, position it successfully once, and then fold the quilt head to the end of the bed by 45cm (note: when throwing the duvet, pull the quilt head backwards as far as possible, if it is not aligned with the bed head, pull it to the bed head when folding the quilt head).

(6) It is required that the center line of the quilt cover should be centered and not deviate from the center line of the bed; The duvet is in place at the four corners of the quilt cover, full and flat. The duvet is flat on both sides of the quilt cover. The surface of quilt cover is flat and smooth. The quilt cover should be flat and closed, so as not to expose the quilt core and tether (note: if the center line of the quilt is off, the quilt cover should be folded back from the short side of the quilt cover).

4, pillowcase:

(1) Shake off the pillowcase, open the pillowcase mouth, lay the pillow core flat on the workbench, fold it vertically, hold both sides of the pillow core with one hand and the pillowcase mouth with the other hand, and put the pillow core into the pillowcase. You can shake it while lifting it, so that all the pillow cores can enter the pillowcase.

(2) Insert the part of the pillowcase beyond the pillow core into the pillowcase, wrap the opening of the pillowcase so that it is not exposed, and seal the bag mouth.

(3) The covered pillow shall have full corners, smooth and crisp appearance, and the pillow core shall not be exposed.

5, put a pillow:

Put the pillow in the center of the bed. Two pillows are required to be stacked neatly, flush with the bedside, with the pillow mouth facing down and the bedside table reversed. The distance between the placed pillow and both sides of the bed is equal, and the surface of the whole pillow is smooth and wrinkle-free. The center line of the pillowcase and the center line of the bed sheet are on the same line (note: when placing the pillow, the opening direction of the pillowcase should face itself, which is convenient for sorting).

6. Operating instructions:

(1) preparation time 1 minute, and operation time is 5 minutes.

(2) The operation is standardized freely, relaxed and compact, with graceful movements and skillful techniques.

(3) It is not allowed to operate at the bedside. During the operation, you are not allowed to run around the bed, kneel on the bed, kneel on the ground or support the bed with your arms, and you are not allowed to let the linen fall to the ground without repeating.

(4) After the operation, the bed should be neat and beautiful, and the whole bed surface should be fresh.

(5) Bedsheet quilt method: the front side is inward, folded in half twice along the long side, and then folded in half twice along the wide side; Folding method of quilt core: S-shaped folding, then both ends are folded to the middle, and then folded in half.