1. Wear labor protection articles as required before operation. If electrical equipment and tools are used, the grounding wire should be checked as required and insulation measures should be taken. 2, check whether the workplace and tools are safe before work, if there are unsafe places and damage, should be cleaned and repaired in time, and put back. 3. It is forbidden to use unqualified tools with cracks, burrs and loose handles, and strictly abide by the safety operation procedures of commonly used tools. 4. Do not wear gloves when drilling and hammering. When drilling with a drilling machine, you must abide by the "Safety Operation Rules of Drilling Machine". 5. Tools must be used to remove iron filings, and it is forbidden to hold them with your hands and blow them with your mouth. 6. When picking and shoveling the workpiece, there shall be no one on the front. When picking and shoveling the workpiece at the fixed workbench, a baffle or wire fence shall be set. 7. Pay attention to the safety of people around you and yourself when working, and prevent the workpieces and tools from falling off and iron filings from splashing and hurting people. When more than two people work, one person should be in charge of the command. 8. When carrying out equipment maintenance, you must apply for a safety maintenance ticket before work. Before entering equipment maintenance, you must apply for a work permit to enter equipment and containers in advance, and you must apply for a hot work permit in advance when entering inflammable and explosive equipment maintenance. 9. When the equipment is overhauled (inspected), the "Contact Sheet for Equipment Overhaul and Power Failure" shall be handled. Electricians should stop sending electricity and take safety measures according to regulations. The operator can directly stop the power-off equipment without going through an electrician. When overhauling, lock the knife switch or hang a "No Closing" sign at the knife switch, and assign a special person to monitor it if necessary. 10. When cleaning equipment workpieces, it is forbidden to use volatile flammable liquids, such as gasoline, benzene, acetone, etc. Fire prevention measures should be taken when necessary.

1 1. When using electrical equipment in wet places and rainy days, it must be checked by an electrician before use. 12, scraping operation, the workpiece must be stable scraper is not allowed to operate on people, grinding large crankshaft, head tile, should set up safety devices or stow wood or take appropriate safety measures. 13. When using the pig, check whether the hose, flexible shaft and electrical grounding are in good condition, and the pig should be closely connected. The operating switch signals of two people must be clear and cooperate with each other, and gloves are not allowed to be worn when pigging. 14. The periphery of the marking table should be kept clean and tidy, and it is forbidden to pile up articles within one meter. The bottom and top of the jack used must be flat, and the thread opening should be tight. It is forbidden to use sliding jack, and the jack is not allowed to tilt. The bottom should be flat, and sleepers should be placed with it. Other personnel shall abide by the safe operation procedures of jack. 15, workpiece marking shall be firmly supported. When supporting a large workpiece, it is forbidden to put your hands under the workpiece. If necessary, you should use a bracket or crane to lift it. If you can't finish it that day, take precautions. 16. When using small lifting equipment, such as chain slings and jacks, the lifting safety operation procedures must be observed. 17. When moving objects manually, it is necessary to have a unified command, make steady progress and keep the same slogan. 18, check the disassembly or assembly work in the middle of the stop or rest, parts must be put safely. 19. When working at heights and using ladders, the "Safety Operation Rules for Working at Heights" and "Safety Precautions for Using Ladders" shall be observed. 20, machinery and equipment before commissioning, first check whether the various parts of machinery and equipment are in good condition, maintenance personnel after leaving the scene, stop sending contact formalities, are not allowed to adjust contact rotating parts during commissioning. The above are collected and sorted by Zhong Da Consulting Company.

For more information about project/service/procurement bidding, and to improve the winning rate, please click on the bottom of official website Customer Service for free consultation:/#/? source=bdzd