The rebar worker refers to the person who uses tools and machinery to derust, straighten, connect, cut off, reshape and install the rebar skeleton. There are four levels of this profession, namely: primary (national vocational qualification level 5), intermediate (national vocational qualification level 4), advanced (national vocational qualification level 3) and technician (national vocational qualification level 2). This profession requires practitioners to have flexible fingers and arms and good physical fitness.

Steel bar workers have become one of the main types of work in the construction industry. Because the construction is mostly in the open air and high places, the construction environment and working conditions are poor and there are many unsafe factors. The composition of field workers is complex and mobile, and there are problems such as poor safety awareness and poor self-protection ability. In the process of construction, there are many phenomena such as illegal command and risky operation, which lead to frequent safety accidents, causing casualties and property losses.

The site must carry out three-level safety education and training for the newly-admitted steel workers, and educate the steel workers on safety production ideas, safety knowledge and safety skills, and special operations personnel should hold relevant certificates.

Extended data:

Operating procedures:

1 steel products, semi-finished products, etc. Should be neatly stacked according to specifications and varieties, the production site should be flat, the workbench should be stable, and the lighting lamps must be covered with nets. ?

Article 2 when the steel bar is straightened, the clamp should be fastened, the ground anchor should be firm and firm, and pedestrians are prohibited within 2 meters along the lacing. Straighten by hand grinding. Don't touch the push rod with your chest and abdomen. Loosen it slowly, not at once.

Article 3. One end of the expanded round steel bar should be fastened to prevent rebound, and it should be stamped with the foot before cutting.

Article 4 the manual cutting, tools must be strong. Stand at an oblique angle when hammering, and pay attention to people and things in the hammer throwing area. Cut short steel bars less than 30 cm, clamp them firmly with pliers, and it is forbidden to hold them by hand, and set a protective box on the outside.

Article 5. When many people jointly transport steel bars, lifting, descending, turning and stopping should be consistent, and manual transmission should not be on the same vertical line. Steel bars shall be dispersed and stabilized to prevent dumping and collapse.

Article 6. Tie steel bars and install skeletons, scaffolding and. Must be set.

Article 7. When binding column and wall reinforcement, it is forbidden to stand on the reinforcement skeleton and climb up and down. The column reinforcement is less than 4 meters, and the weight is not big. It can be tied to the ground or floor and erected as a whole. When the column rebar exceeds 4m, a workbench shall be set. Column beam skeleton should be fixed with temporary support to prevent toppling.

Article 8. When binding foundation reinforcement, steel corbel or horse stool shall be placed according to the construction design regulations to set the upper reinforcement, and the corbel or horse stool shall not be reduced at will.

Article 9. Tethered ring beams, overhangs and external walls of high-rise buildings. When the side column is reinforced, an outer frame or safety net should be set up. Fasten your seat belt when binding.

Article 10. When lifting the steel skeleton, it is forbidden to stand below. You must wait for the skeleton to fall below the ground 1 m before you can get close to it and support it in place before you can unhook it.

Article 1 1. When binding the column and wall reinforcement, it is forbidden to insert the wooden stick or balance beam into the reinforcement skeleton, and sit on the wooden stick or notebook to operate.

Article 12. When the steel bar is too long, the binding shall be firm. Under the command of the rigger, the independent handles of the tower crane and tic-tac-toe crane shall be hoisted to the construction level. If manual transportation is adopted, an operation plan shall be made and the operation shall be carried out under supervision.

Article 13. The steel bars or materials stacked on the operating platform should be reliable, and the operating tools must be packed in tool bags when not in use to prevent falling objects from hurting people.

Article 14. When using cold-drawing machine, cutting machine and bending machine, we should abide by the operating rules of safety technology of reinforcement machinery, and check the reinforcement machinery before use. After use, the power supply should be cut off, and the equipment should be cross-operated (cleaning, lubricating, adjusting, fastening and anticorrosion).

Baidu encyclopedia rebar worker