As shown below, how does this ball machine connect to Dahua's hard disk video recorder (using Yuntai function) ...
Enter the hard disk video recorder setting interface to connect. Set the main menu of video recorder parameters, system settings and pan/tilt settings, select the channel X corresponding to the camera screen, fill in the three parameters of camera address, protocol and baud rate, use the default values for other parameters, save the parameters and exit the menu.
The method/steps are as follows: first, start the hard disk video recorder to connect the monitor, modify the IP, turn on the power of the camera, and connect all cameras and hard disk video recorders with network cables through the switch.
IE logs in Hikvision to check the ONVIF agreement. Generally speaking, the new monitoring needs to manually open the ONVIF protocol. Also, there are locked illegal addresses in security, so don't check them.
Ball machine is generally a variable voltage power adapter for each billiard machine, and the input is 220V household electricity.
How to connect billiards to hard disk video recorder
How to connect billiards to hard disk video recorder
1, enter the hard disk video recorder setting interface to connect. Set the main menu of video recorder parameters, system settings and pan/tilt settings, select the channel X corresponding to the camera screen, fill in the three parameters of camera address, protocol and baud rate, use the default values for other parameters, save the parameters and exit the menu.
2, network hard disk video recorder connected to the ball machine, first of all, you need your ball machine is a network camera.
3. setup. First, enter the main menu of Hikang 642 simulated ball machine video recorder. Secondly, click Yuntai Configuration Settings in Channel Management. Finally, select the corresponding analog ball machine channel to match the video recorder, and then click video.
How to connect ds-2de5 120iw-d ball machine to hard disk video recorder?
How to connect ds-2de5 120iw-d ball machine to hard disk video recorder?
To connect a network hard disk video recorder with a spherical camera, you first need your spherical camera to be a network camera.
If you want to load the ball machine, you should set the hardware of the ball machine: binary dial number (change the original number of the ball machine, which can be set to 1 and 2), and the video lines of the two billiards machines are connected to the video input interface of the hard disk video recorder, usually 75-5 video lines, with Q video connectors at both ends.
Confirm that the address, protocol and communication rate (baud rate) of the camera are the same as those of the corresponding channels of the hard disk video recorder, such as PELCO-9600 and Ya 'an.
T+ and T- should be connected to the back of the video recorder, 485+ on the ball machine should be connected to the T+ of the video recorder, and 485- should be connected to the T- of the video recorder. According to your color, in general, red is a positive power supply and black is a negative power supply. Yellow, green and white, it is recommended to test it to see which one is positive and which one is negative.
Setting method of connecting Dahua network hard disk video recorder to Hikon camera: 1. Click Next to start Dahua Video Recorder and enter the startup wizard.
The following picture shows the wiring diagram of the ball machine: the switch is mainly connected to the camera and video recorder (Nⅴ R) with a network cable.
How to connect Dahua spherical network camera with Hikvision hard disk video recorder?
How to connect Dahua spherical network camera with Hikvision hard disk video recorder?
First open the webpage and log in to Hikon camera, as shown in the figure below, and then go to the next step. Secondly, click Configure in the menu above, then click Network-Advanced Configuration, as shown in the figure below, and then go to the next step.
Open the webpage and log in to Haikang camera. Click Configure in the menu above, and then click Network-Advanced Configuration. Check "Enable onivif" in the Integration Agreement, and then click "Add". In the small window that pops up, create an account name and password, hook the administrator and confirm.
The method of adding Hikvision camera to Dahua mainframe is to start the hard disk video recorder to connect the monitor and modify the IP. The camera power is turned on, and all cameras and hard disk video recorders are connected to the network cable through switches.