Method one

"Materials": table tennis, rubber balls, white latex, rags or scraps of paper, plasticine.

[production process]

(1) Open a hole with a diameter of 3 cm at the top of the rubber ball, and fill the bottom of the ball with plasticine equivalent to about one third of the ball to make the body of the tumbler.

(2) Glue the ping-pong ball to the small round hole of the rubber ball with white latex to make the head of the tumbler.

(3) Cut out the five senses and limbs of the tumbler with cloth horns or colored paper and stick them on the head and body respectively.

Method 2

【 Materials 】 Rice, bowls, chopsticks, toilet paper and eggs.

[production process]

(1) Poke a hole in the top of the egg with chopsticks, stir the egg white and egg yolk with chopsticks, let the egg yolk and egg white flow into the bowl, rinse with water and dry with toilet paper.

(2) Pour some rice into the hole where the egg has just been pierced, and then pour some glue to fix one end of the rice in the egg.

(3) Made a small round hat with colored paper.

(4) Stick the small hat on the hole at the top of the egg.

(5) Draw a face, eyes, nose and mouth for the tumbler.

Method 3

[Materials] Cardboard, table tennis, steel balls or glass balls, crayons, art knives and latex.

[production process]

(1) Make a cylinder out of paper.

(2) Divide the table tennis into two halves, and first stick the middle half on one end of the cylinder.

(3) Put the steel ball or glass ball (which can roll freely inside) into the cylinder, and then stick the other half of the ping-pong ball on the other end of the cylinder to assemble the body of the panda.

(4) Draw your favorite animal head on the outside of the cylinder.

A little animal that can somersault has been made. Put it upright on a page, push it gently, and it will somersault forward.

Make a small drum ~

Method of making: (1) Take an empty bottle (such as iced tea), cut off both ends and leave a middle section. (Make it look like 1, 2 decimeters, anyway, you need the middle section. )

(2) Take the balloon of the toy (that is, the balloon blown out, bigger and better in color) and cut off the blown hole, leaving a large part. Cover the ends of the cut bottle tightly (be careful not to break it, or you can buy another one just in case) and tie it tightly with a string. Tap the balloon membrane gently with a short chopstick (which can be wrapped in crepe paper for decoration), and the balloon membrane will vibrate and sound, and the drum will be ready.

(3) Take a small funnel (which can be made of cardboard) and cover it on the balloon membrane at one end of the drum. At this time, gently pat the film at the other end with your hand, so that the funnel mouth is aimed at the lit candle, and you will find that the flame of the candle tilts and shakes, or even goes out.

A clean eraser with a brush has written wrong words. Use an eraser. After wiping, there will always be a lot of debris left on the paper. It is unsanitary and troublesome to pat by hand or blow by mouth. It won't be so troublesome to make a clean eraser. Material: large rubber, waste brush. Tools: scissors, glue. Manufacturing method: 1. Dig a shallow round hole at one end of the eraser. 2. Remove the tip of the waste brush, clean it and dry it. 3. Cut off the tip of the brush head and turn it into a small brush. 4. Insert the brush head into the small round hole of the rubber and stick it firmly with glue to make a clean eraser. Whenever you finish wiping the eraser, you can gently "sweep" the crumbs off the paper with a brush and then pour them into the wastebasket.

A self-made submarine, a beverage bottle, has a hole in the lid and the bottle body, and a syringe is connected with the hole in the lid through a section of pipe. Put a proper amount of water in the bottle, put the bottle in the sink, and pull the syringe so that there is air in the syringe, otherwise the bottle will float up and down if it doesn't go up.